#Xdax rumlogng voice keyer how to
#Xdax rumlogng voice keyer manual
#Xdax rumlogng voice keyer full
#Xdax rumlogng voice keyer Pc
#Xdax rumlogng voice keyer windows

The VK-64-DX comes without a power supply for stations that use a different power connectors or otherwise want to supply their own 12VDC.

#Xdax rumlogng voice keyer manual

Adding computer control only needs a standard 25 pin shielded computer cable between theĬables are not included, but can be easily made according to directions in the manual orĪ 12V wall transformer with US standard 2 prong plug is included with the VK-64. Transmitter, even when the VK64 is powered off.ĬW set up is as simple as plugging your paddle into the VK-64. Microphone audio and PTT signals pass through the VK-64 and connect directly to the Plug the microphone into the VK-64's microphone input cable. Installing the VK-64 is easy! Unplug the microphone and plug the VK-64's transmitter audio/PTT cable The VK-64 is compatible with the major contest logging programs, including N1MM Logger, NA, WriteLog, TRLog, CT and LogEQF. The delay time can be adjustedįrom approximately 1/2 to 12 seconds with a front panel control. Message 1 for both CW and voice modes can be set up for auto repeat. Logging programs support sending CW through the printer port.Ĭomputer keying works in parallel with the internal CW keyer. The VK-64 also includes a built in LPT CW interface. A front panel knob adjusts speed from 8-45 WPM.

The CW portion is an iambic memory keyer with four programable messages, each one capable of storing over 300 Morse characters. Messages are stored in non-volatile memory, remaining stored until recorded over with a new message. Press the stop button when you are finished. Press the record button followed by a message number button and start talking. The voice keyer section has four 15 second messages.

#Xdax rumlogng voice keyer Pc

You can operate the VK64 manually with the front panel controls or under program control through your PC or laptop's printer port. The VK-64 is a voice keyer and CW memory keyer in the same package! This is a legacy product and is no longer available. However, when RUMlog starts it will overwrite them with the settings stored and managed by RUMlog.ĬW and RTTY memories are always saved permanently.Unified Microsystems: W9XT VK-64 Combo Voice Keyer/CW Memory Keyer and more for ham radio operators!

#Xdax rumlogng voice keyer windows

If you power down the microHAM device and turn it on again while RUMlog is not running you may see different settings if you have configured startup defaults using Windows microHAM Device Router. All the settings can be Saved so that they load the next time you start RUMlog, or Applied temporarily until the next power reset. RUMlog saves the settings and loads them to the microHAM device when it connects to it. Please note that the settings cannot be read from the device, but they can be saved to it. If the window has focus, the following shortcuts are available: Detailed configuration of the many options further described in the device’s microHAM documentation.Show status information when the window is extended.CW keyer configuration additional to Preferences–>CW.Keyer mode switching, depending on your transceiver hardware connection configuration (voice MKII/MKII only).It includes almost all of the functionality described in the microHAM documentation that is supported by the Windows microHAM USB Device Router, although the layout of the options is different. There is a further, dedicated configuration window while connected to DKII, or MKII/MKIII: Menu–>Window–>microHAM. RUMlog internal memories will be ignored when this option is active. Activate this option in Preferences–>µHAM/Fldigi–>microHAM–>Messages.

The internal MKII, MKII, and DKII FSK and CW message memories can be played back using F-keys. Do not configure miroHAM DXP using this preference window.

#Xdax rumlogng voice keyer how to

See the WinKeyer section of the manual for more information how to control it in Preferences–>CW–>WinKey. It works like a WinKeyer and it does not require any further configuration in RUMlog unlike the other microHAM devices. Please note that microHAM DXP is also supported by RUMlog.

This information is saved to the device as soon as you use RUMlog for CAT. The lower section tells the microHAM device what radio it is connected to so that it can perform CAT control. The upper section configures how RUMlog interacts with microHAM. Use Preferences–>µHAM/Fldigi–>microHAM device (MKII or DKII) to configure your DKII, MKII, or MKIII device.

#Xdax rumlogng voice keyer full

RUMlog can configure almost 100% of the settings supported by DKII, MKII, and MKIII and the Windows microHAM USB Device Router software is no longer required for their full use on macOS. MicroHAM devices have very specific configuration options, please see the original microHAM documentation to understand their meaning and function.